Basic Info.
Conductive Type
Bipolar Integrated Circuit
Technics
Semiconductor IC
Product Description
STM32 STM32F429IGT6 MCU Core Board, Full IO Expander, JTAG/SWD Debug Interface
Overview
Core429I is an STM32 MCU core board designed for STM32F429IGT6, supports further expansion. It is ideal for starting application development with STM32F family.
- Minimal ready-to-run system, integrates clock circuit, USB power management, USB connector, etc.
- Onboard 64M Bit SDRAM
- All the I/O ports are accessible on the pin headers
- JTAG/SWD programming/debugging interface
- 2.0mm header pitch, allowed to be plugged-in your application board
What's on the Core429I
- STM32F429IGT6:the high performance STM32 MCU which features:
- Core: Cortex-M4 32-bit RISC
- Feature: single-cycle DSP instructions
- Operating Frequency: 180MHz, 225 DMIPS/1.25 DMIPS/MHz
- Operating Voltage: 1.8V-3.6V
- Package: LQFP176
- Memories: 1024kB Flash, 256+4kB SRAM
- MCU communication Interfaces:
- 6 x SPI, 4 x USART, 4 x UART, 2 x I2S, 1 x SAI, 3 x I2C
- 1 x FMC, 1 x SDIO, 2 x CAN
- 1 x LCD-TFT
- 1 x USB 2.0 HS/FS controller (with dedicated DMA)
- 1 x USB HS ULPI (external PHY required)
- 1 x 10/100 Ethernet MAC
- 1 x 8 to 14-bit camera interface
- AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
- Debugging/Programming: supports JTAG/SWD interfaces, supports IAP
- IS42S16400J: SDRAM 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT)
- AMS1117-3.3: 3.3V voltage regulator
- MIC2075: onboard USB power management device
- Power supply switch, powered from 5Vin or USB connection
- Boot mode selection, for configuring BOOT0 pin
- Power indicator
- VBUS LED
- Reset button
- 8M crystal
- 32.768K crystal, for internal RTC with calibration
- JTAG/SWD interface: for debugging/programming
- USB connector, supports Device and/or Host
- MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion
- 5Vin pinheader, 5V power supply is required when using USB HOST/OTG
- USB OTG/HOST jumper
- short the jumper when using USB OTG/HOST
- open the jumper to disconnect from related I/O port
- VBAT selection jumper
- short the jumper to use system power supply
- open the jumper to connect the VBAT to external power, such as battery
- VREF selection jumper
- short the jumper to connect VREF+ to VCC
- open the jumper to connect VREF+ to other custom pin via jumper wire
Photos
Note:
Mother board or programmer/debugger in the photo is NOT included in the price.
Core429I provides JTAG/SWD debugging interface, yet does NOT integrate any debugging function, a debugger is required.
JTAG/SWD interfaces
The figure 1, and 2 show the header pinouts of JTAG/SWD interface
Figure 1. JTAG Header Pinout
Figure 2. SWD Header Pinout
Development Resources
- Schematic
- Demo code (examples in C, μC/OS-II)
- STM32 development software (KEIL etc.)
- STM32 datasheets
- STM32 development documentation
Dimensions
Address:
Bagualu No. 43, Shenzhen, Guangdong, China
Business Type:
Manufacturer/Factory
Business Range:
Electrical & Electronics
Management System Certification:
ISO 9001
Company Introduction:
Shenzhen waveshare electronics Co., Ltd is a high-tech enterprise, professional research and development and production of Raspberry Pi expansion board, Jetson Nano expansion board and HD LCD / OLED display products, product line more than 10, with independent core technology, innovation ability and good industry reputation, has a hundred intellectual property rights, has more than ten years of industry precipitation.